How To Clean Paint Transfer Of Tail Lights
| ||||||||||||
| Aug 21st, 2006 | ||||||||||||
| ITALGT Member Posts: 994 | I've got some nasty overspray on my tail-light lenses: Anybody have feel taking off the over-spray without ruining the lense? IP: Logged | |||||||||||
| PFF System Bot | ||||||||||||
| Dodgerunner Member Posts: 9682 | I have not tried it on lenses for a few years and so don't know if the plastic has inverse. Only, Anyhow information technology was amazing how it would take stains off paint and lenses without hurting them at all. https://world wide web.hobbylinc.com/htm/mid/mid43-1.htm Be certain it is the stuff yo utilize on paper and balsa woods planes. [This bulletin has been edited by Dodgerunner (edited 08-21-2006).] IP: Logged | |||||||||||
| Firefox Fellow member Posts: 4305 | . [This message has been edited by Firefox (edited 08-22-2006).] IP: Logged | |||||||||||
| Aug 22nd, 2006 | ||||||||||||
| James Bond 007 Member Posts: 8844 | Merely about whatsoever motorcar wax will take that off,it works good to polish plastic too (I employ Turtle wax). IP: Logged | |||||||||||
| 3800superfast Fellow member Posts: 8567 | You don`t want to scratch the lenses--get the clay bar (Clayaway 4 from Pro-Bufford) --then follow with a silconic compound like Duzzall from Pro Bufford, and so follow with MeGuires # 9 swirl remover, then top information technology off with Meguires # 7 mitt glaze, and your good to become. IP: Logged | |||||||||||
| Tom Piantanida Member Posts: 527 | Brqake fluid - yeah, restriction fluid; it lifts paint, but does not set on plastic. And it washes off with h2o. IP: Logged | |||||||||||
| interceptor429 Member Posts: 710 | i've had sucess with wd-xl ,spray on let prepare virtually 10-xv seconds,wipe with a little pressure,its gone , IP: Logged | |||||||||||
| Aug 23rd, 2006 | ||||||||||||
| ITALGT Member Posts: 994 | ...thank you for the suggestions guys, I'yard trying them as we speak... er, type... Brett IP: Logged | |||||||||||
| Indiana_resto_guy Fellow member Posts: 7158 | If the overspray has been there for a while (long enough to dry good) use rubbing chemical compound. IP: Logged | |||||||||||
| Mickey_Moose Member Posts: 7326 | restriction fluid will piece of work equally meantioned above, just brand certain you don't become it on the paint yous want to go on. brake fluid is an quondam modelers trick for pigment removal when edifice model planes/boats/cars/etc. IP: Logged | |||||||||||
| trots Member Posts: 238 | on a side note, that paint looks crawly. cany pics of the whole car? ------------------ IP: Logged | |||||||||||
| PFF Organisation Bot | ||||||||||||
| Brian Lamberts Member Posts: 2691 | Yup, use brake fluid. I'd test it on a hidden portion before putting it on the visible, just to be safety. But the lenses should exist safe from brake fluid, and the over spray will soften and come right off. IP: Logged | |||||||||||
| Francis T Member Posts: 6620 | On the topic of plastic lenses, I recently got some mothers plastic polish for the headlites on my Ranger equally they were very frosty. Boy that stuff works great! Did my wife's Cirris too. And now I'm going to exercise the rear lenses on my 86 and 87 GTs. Now if there was merely manner to get those air-like pockets out them besides. IP: Logged | |||||||||||
| ITALGT Member Posts: 994 | Update... I've soaked the lenses with brake fluid for about ii days, but even so wouldn't budge the paint... so, I ended up using a scotch-brite pad and alcohol. I've got the over-spray off now, but tomarrow I will exist getting some rubbing compound and do some buffing. I recall I should exist able to get them to polish once again... I'll mail service pictures of the results... Brett IP: Logged | |||||||||||
| Starfighter Member Posts: 182 | Ihave taken scratches out of lenses by sanding with 1500 and so 2000 then some rubbing chemical compound then wax and they await like amend so the twenty-four hours the came out of the factory.pretty scary the commencement fourth dimension until you run across the end result and it does non accept long at all. Jim IP: Logged | |||||||||||
| Aug 25th, 2006 | ||||||||||||
| Xanthous-88 Member Posts: 454 |
This is past far the best manner to restore clear plastic. The process Jim discribs is the aforementioned one used on very loftier end paint jobs to not only shine the surface, but flatten sutble ripples. Useing a hard cake under the wet sandpaper tin make an iregular surface mirror flat. On the curved lense of a GT, you wouldent utilise a block. IP: Logged | |||||||||||
| Aug 28th, 2006 | ||||||||||||
| ITALGT Fellow member Posts: 994 | Ok, time for an update... I successfully removed the overspray using a scotchbrite pad and alcohol, equally posted before... I also scuffed the residual of the lenses repeatedly, working out some of the scuffs and scratches. These scotchbrite pads are just coarse enough to work out some of scratches and swirl-marks. Information technology actually works pretty well: After scuffing, I got out the power-buffer and attacked the lenses with rubbing chemical compound, followed by some plastic polish and a couple of coats of wax. Here's the results: I was actually quite surprised how well they came out, and it wasn't all that tough. I didn't do a perfect job on these, just I'll exist replacing them in the future with something custom anyway... so information technology's proficient for now. The adjacent step is to tint the lenses for that "blacked-out" expect... Thank you again for all of your suggestions and insight... that's what I dearest about this forum! [This message has been edited by ITALGT (edited 08-28-2006).] IP: Logged | |||||||||||
| RWDPLZ Fellow member Posts: 14725 | ||||||||||||
| 2002z28ssconv Member Posts: 1435 | I had bought a Mother's power ball for the wheels on my Camaro. It worked great on the wife's 88 GT lenses too. Merely in example anyone had a drill and no buffer. I have a buffer too. The power ball was merely easier to get to in my garage - lol. IP: Logged | |||||||||||
| fierofetish Fellow member Posts: 19173 | I always utilise a handcleanser purchased from my paint store. It has multiple weak solvents in it, and a very fine abrasive.Information technology is strong enough to dissolve paint on your hands without damage, and so I therefore ended information technology would remove overspray on almost other surfaces, without scratching or melting the surface. Works like a dream..removing overspray from painted surfaces, rubber, plastic, drinking glass...and, of course...hands IP: Logged | |||||||||||
| ITALGT Member Posts: 994 |
I would take NEVER thought of that... cheers for the info! IP: Logged | |||||||||||
| PFF System Bot | ||||||||||||
| Aug 29th, 2006 | ||||||||||||
| 3800superfast Member Posts: 8567 | ITALGT, Overnice Job !!! Cheers for posting the pics & how to`s. IP: Logged | |||||||||||
| rogergarrison Fellow member Posts: 49601 | Scotchbrites are courser than 1500-2000 paper. I practise LOTs of headlights. I wet sand with 1500, and then power buff with 3M super duty compound. They look like new. IP: Logged | |||||||||||
!!
Source: https://www.fiero.nl/forum/Archives/Archive-000001/HTML/20070315-2-076209.html
Posted by: plylerdowits1958.blogspot.com
0 Response to "How To Clean Paint Transfer Of Tail Lights"
Post a Comment